Box 1.7, in addition to teardown, no other method can brush recovery, and ROOT
The posting method on the forum is short-circuited.
Forum address posted on the forums: Lynx Box 1.7.0 system root, recovery, short circuit brush, graphic tutorial
First of all, the second step of this tutorial,
2. After plugging the sd card into the computer, unzip the attachment, open SDcardMaker.exe, select the drive letter corresponding to the sd card, select uboot.bin according to the instructions, and after the burning is completed, add the other recovery.img, update_root.zip in the attachment. Copy to sd card.
In this operation, do not use U disk instead of SD card, open SDcardMaker.exe, to select the format,
After the sd card is made, there is a sd card slot behind the box, which should be inserted directly into the SD card slot.
There is also a very important key point. The landlord did not say that I had at least tried more than 10 times and could not succeed. And after more than ten times, the box has been successfully bricked. The boot always stopped at the first LOGO screen and I couldn't move forward. When I was cold, and after I turned bricks, I couldn't get into any files even though I was short, but I couldn't write any files. Then I checked on the Internet and learned that A certain key point, release the short-circuit in time, will not succeed if you do not release it. The key point on the Internet at that time was the blue light. In fact, this was wrong. I tried many times and failed.
The really important key point is, when you see a signal on the TV, quickly release the short.
Let me elaborate on this again.
When short-circuiting, first dial down the power, start shorting, and then insert the power, (the best time between dialing and plugging is longer, it is better to have more than three minutes, the time is short, I suspect there is still some power in the box, Not easy to succeed,)
After plugging in the power, wait a few seconds until the light of the box is on. After the light is on, keep shorting.
Then when you see the beginning of a signal input on the TV, it is obvious that there is a flash on the TV.
If you have been short-circuited, you can enter the rec interface, but you can't do it anyway. Always fail,
In addition, there is a mistake in the postings posted on the forum. When you select a file, update.zip is used on the image. However, the actual extracted file is update_root.zip. The solution is either you renamed it or choose choose zip from. Sdcard and then choose update_root.zip
After the system root, it is recommended to install the restart software. This software can automatically enter the rec interface when restarting.
Download address: http://bbs.shafa.com/thread-1275909-1-1.html
Talking about this brush machine, I was really tired and got it for a few days.
Finally, after the cover of the box was removed, the iron was not removed. I saw that everyone else took off the iron and used fine scissors or the like to insert it between the two feet, but I didn't know how to take it. The fear is broken,
My method is:
Get a thin wire between the two feet, do not touch the other foot.
My thin wire has plastic insulation outside, leaving only the front slightly outcropped and interposed between the two feet.
If you don't have insulation, it's best to wrap it in clear plastic and only expose the front end a little.
The posting method on the forum is short-circuited.
Forum address posted on the forums: Lynx Box 1.7.0 system root, recovery, short circuit brush, graphic tutorial
Lynx Box Exchange 3 Group
First of all, the second step of this tutorial,
2. After plugging the sd card into the computer, unzip the attachment, open SDcardMaker.exe, select the drive letter corresponding to the sd card, select uboot.bin according to the instructions, and after the burning is completed, add the other recovery.img, update_root.zip in the attachment. Copy to sd card.
In this operation, do not use U disk instead of SD card, open SDcardMaker.exe, to select the format,
After the sd card is made, there is a sd card slot behind the box, which should be inserted directly into the SD card slot.
There is also a very important key point. The landlord did not say that I had at least tried more than 10 times and could not succeed. And after more than ten times, the box has been successfully bricked. The boot always stopped at the first LOGO screen and I couldn't move forward. When I was cold, and after I turned bricks, I couldn't get into any files even though I was short, but I couldn't write any files. Then I checked on the Internet and learned that A certain key point, release the short-circuit in time, will not succeed if you do not release it. The key point on the Internet at that time was the blue light. In fact, this was wrong. I tried many times and failed.
The really important key point is, when you see a signal on the TV, quickly release the short.
Let me elaborate on this again.
When short-circuiting, first dial down the power, start shorting, and then insert the power, (the best time between dialing and plugging is longer, it is better to have more than three minutes, the time is short, I suspect there is still some power in the box, Not easy to succeed,)
After plugging in the power, wait a few seconds until the light of the box is on. After the light is on, keep shorting.
Then when you see the beginning of a signal input on the TV, it is obvious that there is a flash on the TV.
If you have been short-circuited, you can enter the rec interface, but you can't do it anyway. Always fail,
In addition, there is a mistake in the postings posted on the forum. When you select a file, update.zip is used on the image. However, the actual extracted file is update_root.zip. The solution is either you renamed it or choose choose zip from. Sdcard and then choose update_root.zip
After the system root, it is recommended to install the restart software. This software can automatically enter the rec interface when restarting.
Download address: http://bbs.shafa.com/thread-1275909-1-1.html
Talking about this brush machine, I was really tired and got it for a few days.
Finally, after the cover of the box was removed, the iron was not removed. I saw that everyone else took off the iron and used fine scissors or the like to insert it between the two feet, but I didn't know how to take it. The fear is broken,
My method is:
Get a thin wire between the two feet, do not touch the other foot.
My thin wire has plastic insulation outside, leaving only the front slightly outcropped and interposed between the two feet.
If you don't have insulation, it's best to wrap it in clear plastic and only expose the front end a little.