Package package will be it! 10 minutes quick install tutorial

Yesterday, the oil (you) comments in the comments area attracted small editors. “I'm very fond of pushing you a lot of content, but can you push the tutorial on how to install? Install it! "Oh, well, Xiao Bian talked about it a bit, and it makes sense. Xiao Bian pushes a concise tutorial on how to install the machine today.

In fact, there is a sequence of computer installed, the motherboard's baffle must first be installed on the chassis! First of all to install to the chassis! First of all to install to the chassis! Three important things to say. In fact, Xiao Bian often forgets that all the motherboards are ready to be put into the chassis before they are found, ah ... there is also the power supply must be installed inside the chassis, but now many packages are chassis + power supply package installed, Xiaobian not More to say.

The first wave: CPU, fan installed

Take out the CPU and, in turn, look at the recesses on the left and right. This corresponds to the corresponding position of the CPU socket. Pull open the protective cover of the motherboard CPU slot and install the CPU corresponding notch to the motherboard.

Put on the protective cover, press down on the lever, and the CPU is installed. At this time, you can apply silicone grease on the top of the CPU (silicone, not silicone, silicone can't get it down).

A total of four holes are installed in the CPU fan, and the four snaps are pressed and installed according to the diagonal principle. If it is a screw + backplane, it will be easier.

Turn over the back of the motherboard to see if the locking mechanism in the buckle is in place (actually the same reason as the expansion bolt)

Finally, we must remember to plug the power cord of the CPU fan into the motherboard. Generally, the motherboard will print the word “CPU FAN”. Please note that there is an anti-plug design. Do not make mistakes (violence installation can also be inserted...).

Second Wave: Fixed Motherboard

Xiao Bian's order is a summary of thousands of installations. At this time, instead of installing a memory card, the motherboard is installed. Because the mounting hole is too deep, it is not easy to use a screwdriver after installing the memory and graphics card.

ATX, MATX, and even ITX, in fact, a large part of the hole spacing is consistent with the standard, starting from 1 in the figure below to the right, ITX, MATX and ATX hole pitch no difference, only the length difference. When installing, regardless of the type of version, it must be in accordance with the diagonal screw fixation, so that the motherboard is not easy to be distorted (stress problem).

It should be noted that when installing screws 1 and 2 in two places, do not tighten them up, leave a little squeaking, and tighten them after other screws are tightened and fixed. This is better.

The third wave: memory, graphics card installation

After installing the motherboard, you can install the memory and graphics card. Xiaobian strongly recommends that you first install the memory and then install the graphics card. In fact, computer accessories have anti-plug design, memory is also the case. Regardless of DDR3 or DDR4, there is a gap in the memory. Insert this slot into the motherboard memory slot.

When inserting, the first half is inserted into the memory slot first, and when the other snap is released, the memory is pressed down, and a “click” sound is heard, and the memory snap is closed even if the installation is completed.

Next is the graphics card, the graphics card has a locking and locking mechanism at the tail, a bit like a hook, the motherboard also has a locking buckle at the corresponding slot position.

Loosen the clips on the motherboard graphics card slot, align the end of the graphics card, push the card into the slot from the back and forth, and hear the snap-fastened sound even if it is a work. Another thing to note is that there is also a special design on the front of the motherboard graphics card slot. In fact, there is a PCI-E × 1 standard slot.

Fourth Wave: Power Supply Ports

After installing the graphics card, you can begin to install the power wiring. The brunt of this is motherboard power supply. There are two main board power supplies, one is the auxiliary power connector (8 pins) near the CPU and various backplane interfaces, and the other is the 24-pin main power interface.

Its shape is very good to identify, when the installation is also aligned with the side of the buckle (the main board of wood, the power line for the male) under the pressure on the line, be careful not to excessive force, can hear the buckle locking sound. Too hard to insert can easily cause permanent deformation of the motherboard.

Next is the auxiliary power supply and graphics card power supply, the interface looks a lot like, but the graphics card for the dual 6-pin interface (a small part of the dual 6 +2), this point and the auxiliary power interface is a bit different. When installing, just like the main power supply, just follow it.

The fifth wave: difficult to start the connection is coming!

Switch connection is probably the hardest place for many people to think, because basically all of them are small pins, and it is not easy to distinguish between positive and negative directions, but this part of Xiaobian is very good.

First look at the motherboard pin, notice the pin below the pin to identify the location of the width of the box and the positive and negative printed logo? We just want to correspond to the logo installation here

Some chassis pins are printed with positive and negative electrodes and function texts, but some only print functional texts without positive and negative poles. How do you install them?

In fact, regardless of whether the pin is printed or not, there must be a mark on the back! Looking at the pins in reverse, each pin will have a small triangular mark on one side. This triangular mark is the positive (+) mark, as long as the positive and negative pins are inserted in front of the main board pin position (+ to +). -Correct-). PowerSW corresponds to PowerSWF (power switch), RestSW corresponding to RestSW (restart), HDD LED, and PowerLED respectively. It's that simple! Incidentally, the USB pins and so on are all the same, as long as the + positive position is correct!

The sixth wave: closing the hard drive it!

The last step is to install the data cable and power cable of the hard disk. One end of the motherboard connects to the data cable according to the shape of the interface. Also, don't worry too much about SATA1 or SATA. Now the delay of boot sequence is almost negligible. One data cable on the motherboard is connected, which is the hard disk part. Do you see the golden interface pins? The power line is wider, and the data line is narrower. Corresponding to anti-plug design and installation on the line, there is almost no technical content, very simple.

This installation sequence is the experience of Xiaobian's long-term installation. The advantage is that the sequence is clear. It is not easy to fight with each other during internal installation. It affects the installation (excluding the CPU heat sink), and this sequence is the fastest. Well, if you have any questions, the comments section will comment on the best.