1 Introduction
　　 Wireless sensor networks are often accompanied by a large number of sensor devices. If you connect various devices to the Internet, you need a large number of IP addresses. At present, IP v4 cannot meet their needs, and IPv6 has rich address resources, so it can be very good. To meet its needs, IPv6 also has the following advantages:
1.1 High security
The IP v6 protocol family defines basic information about security, such as Datagram Encapsulation Security Protocol (ESP) and Send Datagram Authentication (Authentication Header AH).
For all IPv6 nodes, IPsec is mandatory. An IP v6 end-to-end connection is secure. The verification of the communication peer verifies the encryption and protection of data so that sensitive data can be safely transmitted on the IPv6 network. And the globally unique address can clearly identify each node, and avoid the end-to-end security damage of NAT (Network Address Translation).
1.2 Strong mobility
You can obtain a care-of address from anywhere through address auto-configuration, and use this address to communicate with nodes on the network. With mobile IPv6 and home agent, mobile terminals can roam between different networks while keeping existing communication connections uninterrupted, while maintaining their own reachability.
1.3 Good service quality
There is a Traffic Class in the IP v6 packet header, which can be used to implement priority services for key users and applications; the flow label field in the IPv6 packet header is Traffic Engineering and load balancing And distinguishing end-to-end data streams provides a powerful tool; globally unique addresses can distinguish data streams in more detail, while structured addresses can easily implement data stream aggregation on edge networks.
Therefore, IP V6 can meet the functional requirements of seamless connection between wireless sensor networks and the Internet.
2 Research on key technologies
A wireless sensor network is a multi-hop mobility peer-to-peer network that uses wireless communication and consists of a large number of sensor nodes with wireless communication and computing capabilities, low power consumption, and low complexity. If the IP V6 technology is fully applied to the wireless sensor network, it will inevitably consume most of the energy of the sensor, and some of its functions cannot be realized. Therefore, the existing IPV6 technology cannot be applied to wireless sensor networks. In order to apply IP V6 technology to wireless sensor networks, this paper designs the IPV6 header compression method based on the study of 6L o W PA N, so that IPV6 can effectively serve wireless sensor networks. The IEEE working group designed the IPv6 header compression method shown in Figure 1.
Figure 1 LOWPAN_HC1
In this design, the source address and destination address of IPV6 occupy a large part of the data packet space. If the address space occupied by it can be optimized and compressed, the working efficiency of the data packet will be greatly improved. The main address of the IP V6 data packet mainly includes the address prefix and the interface identification. If it is transmitted inside the wireless sensor network, the prefix can be compressed completely, and the interface identification can be identified through the data link layer. On this basis, the source address and destination address can be effectively compressed into 2 bits. The specific design format is shown in Figure 2:
Figure 2 LOWPAN_HC1 encoding format
The specific encoding format is described as follows:
SA: IPV6 source address
DA: IPV6 destination address
T & F: transmission type and data flow label
NH: Next head
HC2: HC2 code
NCF: uncompressed area
3 Simulation experiment
In order to verify the effectiveness of the method designed in this paper, the design method was simulated on the N S2 simulation. The experiment mainly includes 21 nodes, simulating the experiment in a space of 50 * 50 square meters, including 1 demodulator and 5 common coordinators. The length of the simulated reference layer data information is 50 bytes. The main experimental content includes information transmission success rate and end-to-end delay test. The specific test results are shown in Tables 1 and 2.
Table 1 Comparison of data packet transmission success rate
Table 2 End-to-end delay comparison
4 Summary
In this paper, based on the research of wireless sensor networks, IP V6 and 6LoWPAN, the headers of IPV6 data packets are partially optimized and compressed, so that IPV6 can be better applied to wireless sensor networks, which can make wireless sensor networks Good integration with the Internet.
Push Button Switches
The Push Button Switches, also known as the control button (referred to as the button), is a low-voltage electrical appliance that is manually and generally can be automatically reset. The Push Button Starter Switch is usually used to issue a start or stop command in the circuit to control the turning on and off of electrical coil currents such as electromagnetic starters, connectors, and relays.
The On Off Push Button Switches refers to a switch that pushes the transmission mechanism with a button to make the movable contact and the static contact open or close and realize circuit switching. It is a master control device with a simple structure and a wide range of applications. In the electrical automatic control circuit, used to manually send control signals to control connectors, relays, electromagnetic starters, etc.
This Pushbutton Switches is a kind of electric device that is used to switch on and off the small current circuit when the action is released. Generally used in AC and DC voltage below 440V, the current is less than 5A in the control circuit, generally do not directly manipulate the main circuit can also be used in the interconnection circuit. In actual use, in order to prevent desperation, different marks are usually made on the buttons or painted with different colors, and the colors are red, yellow, blue, white, black, green, and the like.
The Momentary Push Button Switch could be divided into metal push button switches and LED Light Switches and ordinary snap button type, mushroom head type, self-locking type, self-resetting type, rotary handle type, with indicator light type, lighted symbol type and key type, etc., with single button and double Buttons. Generally, it adopts a water-storage structure, which consists of a button cap, a return spring, a static contact, a moving contact and a casing. It is usually made into a composite type, and has a pair of normally closed contacts and normally open contacts, and some products can pass. The series connection of multiple elements increases the number of contact pairs. There is also a self-contained button that automatically holds the closed position when pressed, and can be turned on only after the power is turned off.
When the Metal Switches is not pressed, the movable contact is connected with the upper stationary contact. The pair of contacts is called a normally closed contact. At this point, the movable contact is disconnected from the following static contact. The pair of contacts is called a normally open contact: the button is pressed, the normally closed contact is open, the normally open contact is closed, and the button is released. Restore the original working state under the action of the return spring
Push Button Switches,Push Button On Off Switch,Push Button Switch Types,Square Push Button Switches
YESWITCH ELECTRONICS CO., LTD. , https://www.yeswitches.com