Nowadays, all kinds of audio have entered thousands of households, and people can enjoy beautiful music at any time. However, when using audio equipment, you must not neglect every link, even the switch that uses the audio is very knowledgeable, otherwise it will affect the working performance of the sound and shorten the service life. So how do you use the audio switch correctly?
The first is the boot sequence. After turning on the power, first turn on the sound source part, that is, the laser record player, deck, tuner, record player, etc., select one, and then open the equalizer. If the battery is opened first, this will damage the life of the supply and the tweeter of the speaker.
Followed by the volume control. Before turning on the power, the knob of the volume should be at 0 position, and then gradually open from small to moderate. Do not change the mode of operation such as mono, stereo or bridge at will when you turn it on. At the end of the shutdown, turn the volume knob to 0.
The third is the shutdown sequence. Turn off the supply and discharge, then turn off the amplifier, equalizer, and CD player, record player, etc., so that when the power of other devices is cut off, the anti-peak voltage will not be applied to the supply. It should be noted that do not cut off the power at once.
At the same time, the use of security is also an important aspect. In order to protect the supply and the speaker, you can install a quick-blow fuse and fuse on the supply and speaker wiring or on the tweeter circuit to protect the sound and tweeter. In addition, do not plug in the sound source parts such as CD players, decks, record players, etc. while the power supply or volume knob is on. Also don't open the speaker. Because the two terminals of the speaker are very close, pay attention to avoid accidentally shorting the two wires of the speaker and burn the amplifier. Nowadays, all kinds of audio have entered thousands of households, people Enjoy beautiful music at any time. However, when using audio equipment, you must not neglect every link, even the switch that uses the audio is very knowledgeable, otherwise it will affect the working performance of the sound and shorten the service life. So how do you use the audio switch correctly?
The first is the boot sequence. After turning on the power, first turn on the sound source part, that is, the laser record player, deck, tuner, record player, etc., select one, and then open the equalizer. If the battery is opened first, this will damage the life of the supply and the tweeter of the speaker.
Followed by the volume control. Before turning on the power, the knob of the volume should be at 0 position, and then gradually open from small to moderate. Do not change the mode of operation such as mono, stereo or bridge at will when you turn it on. At the end of the shutdown, turn the volume knob to 0.
The third is the shutdown sequence. Turn off the supply and discharge, then turn off the amplifier, equalizer, and CD player, record player, etc., so that when the power of other devices is cut off, the anti-peak voltage will not be applied to the supply. It should be noted that do not cut off the power at once.
At the same time, the use of security is also an important aspect. In order to protect the supply and the speaker, you can install a quick-blow fuse and fuse on the supply and speaker wiring or on the tweeter circuit to protect the sound and tweeter. In addition, do not plug in the sound source parts such as CD players, decks, record players, etc. while the power supply or volume knob is on. Also don't open the speaker. Because the two terminals of the speaker are very close, pay attention to avoid accidentally shorting the two wires of the speaker and burn the amplifier. Nowadays, all kinds of audio have entered thousands of households, people Enjoy beautiful music at any time. However, when using audio equipment, you must not neglect every link, even the switch that uses the audio is very knowledgeable, otherwise it will affect the working performance of the sound and shorten the service life. So how do you use the audio switch correctly?
The first is the boot sequence. After turning on the power, first turn on the sound source part, that is, the laser record player, deck, tuner, record player, etc., select one, and then open the equalizer. If the battery is opened first, this will damage the life of the supply and the tweeter of the speaker.
Followed by the volume control. Before turning on the power, the knob of the volume should be at 0 position, and then gradually open from small to moderate. Do not change the mode of operation such as mono, stereo or bridge at will when you turn it on. At the end of the shutdown, turn the volume knob to 0.
The third is the shutdown sequence. Turn off the supply and discharge, then turn off the amplifier, equalizer, and CD player, record player, etc., so that when the power of other devices is cut off, the anti-peak voltage will not be applied to the supply. It should be noted that do not cut off the power at once.
At the same time, the use of security is also an important aspect. In order to protect the supply and the speaker, you can install a quick-blow fuse and fuse on the supply and speaker wiring or on the tweeter circuit to protect the sound and tweeter. In addition, do not plug in the sound source parts such as CD players, decks, record players, etc. while the power supply or volume knob is on. Also do not open the speaker, because the two terminals of the speaker are very close, pay attention to avoid accidentally shorting the two wires of the speaker and burning the amplifier.
The first is the boot sequence. After turning on the power, first turn on the sound source part, that is, the laser record player, deck, tuner, record player, etc., select one, and then open the equalizer. If the battery is opened first, this will damage the life of the supply and the tweeter of the speaker.
Followed by the volume control. Before turning on the power, the knob of the volume should be at 0 position, and then gradually open from small to moderate. Do not change the mode of operation such as mono, stereo or bridge at will when you turn it on. At the end of the shutdown, turn the volume knob to 0.
The third is the shutdown sequence. Turn off the supply and discharge, then turn off the amplifier, equalizer, and CD player, record player, etc., so that when the power of other devices is cut off, the anti-peak voltage will not be applied to the supply. It should be noted that do not cut off the power at once.
At the same time, the use of security is also an important aspect. In order to protect the supply and the speaker, you can install a quick-blow fuse and fuse on the supply and speaker wiring or on the tweeter circuit to protect the sound and tweeter. In addition, do not plug in the sound source parts such as CD players, decks, record players, etc. while the power supply or volume knob is on. Also don't open the speaker. Because the two terminals of the speaker are very close, pay attention to avoid accidentally shorting the two wires of the speaker and burn the amplifier. Nowadays, all kinds of audio have entered thousands of households, people Enjoy beautiful music at any time. However, when using audio equipment, you must not neglect every link, even the switch that uses the audio is very knowledgeable, otherwise it will affect the working performance of the sound and shorten the service life. So how do you use the audio switch correctly?
The first is the boot sequence. After turning on the power, first turn on the sound source part, that is, the laser record player, deck, tuner, record player, etc., select one, and then open the equalizer. If the battery is opened first, this will damage the life of the supply and the tweeter of the speaker.
Followed by the volume control. Before turning on the power, the knob of the volume should be at 0 position, and then gradually open from small to moderate. Do not change the mode of operation such as mono, stereo or bridge at will when you turn it on. At the end of the shutdown, turn the volume knob to 0.
The third is the shutdown sequence. Turn off the supply and discharge, then turn off the amplifier, equalizer, and CD player, record player, etc., so that when the power of other devices is cut off, the anti-peak voltage will not be applied to the supply. It should be noted that do not cut off the power at once.
At the same time, the use of security is also an important aspect. In order to protect the supply and the speaker, you can install a quick-blow fuse and fuse on the supply and speaker wiring or on the tweeter circuit to protect the sound and tweeter. In addition, do not plug in the sound source parts such as CD players, decks, record players, etc. while the power supply or volume knob is on. Also don't open the speaker. Because the two terminals of the speaker are very close, pay attention to avoid accidentally shorting the two wires of the speaker and burn the amplifier. Nowadays, all kinds of audio have entered thousands of households, people Enjoy beautiful music at any time. However, when using audio equipment, you must not neglect every link, even the switch that uses the audio is very knowledgeable, otherwise it will affect the working performance of the sound and shorten the service life. So how do you use the audio switch correctly?
The first is the boot sequence. After turning on the power, first turn on the sound source part, that is, the laser record player, deck, tuner, record player, etc., select one, and then open the equalizer. If the battery is opened first, this will damage the life of the supply and the tweeter of the speaker.
Followed by the volume control. Before turning on the power, the knob of the volume should be at 0 position, and then gradually open from small to moderate. Do not change the mode of operation such as mono, stereo or bridge at will when you turn it on. At the end of the shutdown, turn the volume knob to 0.
The third is the shutdown sequence. Turn off the supply and discharge, then turn off the amplifier, equalizer, and CD player, record player, etc., so that when the power of other devices is cut off, the anti-peak voltage will not be applied to the supply. It should be noted that do not cut off the power at once.
At the same time, the use of security is also an important aspect. In order to protect the supply and the speaker, you can install a quick-blow fuse and fuse on the supply and speaker wiring or on the tweeter circuit to protect the sound and tweeter. In addition, do not plug in the sound source parts such as CD players, decks, record players, etc. while the power supply or volume knob is on. Also do not open the speaker, because the two terminals of the speaker are very close, pay attention to avoid accidentally shorting the two wires of the speaker and burning the amplifier.
Mica Tape,Single-Side Fiber Brown Mica Tape,Tung Oil-BMI-Expoxy Mica Paper
Thermal Expansion Sheet Co., Ltd. , http://www.insulation-sheet.com